Types of Plumbing systems

As for his own plumbing can save you a lot of money, but simply does not require a lot of plumbing work knowledge and skills. Beginners should be able to manage simple jobs like replacing a tap washer, or water in the pool, and the average handyman should be able to handle more complex work such as plumbing a separate shower. But you should think twice before trying to tackle a very complex task. Work on the sewer system can be dirty business – especially if you have to lift the floor or work in a dusty attic and quite strenuous.

Two major parts of household plumbing system – a system of water supply and waste management system. The water system is a series of pipes and fittings, which brings clean water for baths, pools, bathrooms, etc.. Waste system, another set of pipes that carry water to the drainage system can be used anywhere. An old house, or one of the many water pipes fit ¬ settings seem very confusing, but the basic vertical ¬ ing system is really very simple. Before starling the plumbing works in each line of the track carefully so you know where all the lead pipe, and what it does.

Water supply
Household water plumbing system basically starts the enterprise (or a water authority or company) team. This is usually located outside the borders of the property is 750 mm below the ground under a small metal cover, probably on the sidewalk. Most of the water stop cocks ¬ company needed a special key to switch them on and off. Valve regulates the flow of water between the water in the water, and the main water supply. The tube that carries the water from the tap to the house known as the aqueduct, and the responsibility for maintenance lies with the owner. Before 1939, general service tubes, steel or lead, and now adays ¬ often copper or polyethylene. Many service pipes up, such as water shut ¬ crane, as the house, but always at least 750 mm below ground. Once in the house pipes (called a rising main) can be protected from freezing by running an inner wall. Discontinued floor at home, if necessary additional protection to the pipe freezing.

There are two basic systems for moving water in the house, where people wanted to rising toplaces directly and indirectly.

Useful resources: –finish basement Cumming GA | Showers Cumming GA | remodels Roswell GA

Indirect plumbing systems in an indirect system, the main PUR ¬ represents the rising of the people that feed water into the cold water cistern (sometimes mistakenly called the bath), which is usually located in the attic. Most of the faucets and other plumbing fixtures in the house to get water from the tank, which is shorter, from sunrise through the main ballvalve. However, at least one cold water tap in the kitchen tour in general must be powered directly from the rising main to supply drinking water.

Depending on whether the local water regulations, one, two or more plants can be directly to the rising main – one of the tour leads to ¬, and a cold water washing machine or dishwasher ¬, “he says. Another connection can be made and electric shower.

The two most direct water pipe (often referred to as dried tubes) and water tank. The pipe-emission toilets and cold water taps in the bath room and other rooms ¬ where pools. Other electric hot water cylinder where water is stored and heated in a boiler or heating Emir ¬ SION. Cold water tank for further draw-off pipes of certain types of bidet or a shower, and that some pipeline facilities are much more comfortable.

Immersed in hot water taps for hot water pipes associated with the upper cylinder – again, bidet and shower facilities on their own, indi ¬ ties. ¬ der of hot water bottles will also have a pipe leading back to the cold water tank safety vent that air bubbles and steam to escape.

Perform work in the plumbing system, or to stop the leak or explosion, ¬ ToRs other parts of the system must be isolated and drained of water. In theory, only one valve or the valve is really needed is a system. This should be as close as possible to the point where the main service pipe enters the house that the whole house must be insulated from the water. Draincocks two are needed – just one of the main drain valve to the rising main and each branch is connected to it, others low as possible to probe the hot water cylinder until the cylinder. Cranes feeding tubes, hot and cold taps, flushing cisterns and cold water tank associated itself drained by turning the tap. This is how ¬ ever, drain the hot water cylinder.

In fact, to save having to drain the system each time repairs done better, more stopvalves that, in some parts of the plumbing system is isolated from the rest. This usually leads to the door of each channel tank valves. It is possible that a small isolation valves before each valve or fitting. There can be no valve on the outlet pipe hot water bottle.

Direct water supply systems
Direct plumbing system, all the cold taps, toilets, etc., are fed directly to the rising main. If hot water is heated by hot water storage cylinder (not instant water heaters), it is usually fed by a small container of cold water is often at the top of the glass.

Which system is best?
Indirect plumbing system has three main advantages. First, and perhaps most importantly, because most of the water tank system is isolated from the network is unlikely to be drawn back into the network (this is called back siphonage), making it much less risk of water pollution. Second, the system is in a constant water pressure, so you do not have to worry about changes in network pressure – this is particularly important for some showers, it’s roughly the same pressure hot and cold water. Finally, the cistern provides a water reserve, if the network does not.

Direct pipeline system is a bit less complicated and cheaper to install than an indirect one. But some adjustments need to be developed to fit ¬ used to reduce the risk of contaminat ¬ ing network.

The type of system has the potential will be determined by the local water supply company. The last option is to unvented hot water. Here is the cold supply to the house of the system, the direct above, but (mostly) hot water bottle is fed directly from the rising main. Unvented hot water systems must be properly installed and maintained, but a number of advantages over conventional  auxiliary systems.


Leave a comment

Filed under Uncategorized

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s